Is Leasing a Coil Line Cheaper Than Buying One?
- Share
- publisher
- David Park - Senior Stamping Engineer, FANTY Machinery
- Issue Time
- Nov 19,2026
Summary
A 48-month lease at 2.35 percent a month costs 221,040 USD on a 180,000 USD line, against 205,020 USD for a bank loan and 174,600 USD for cash. The article works through the five-year arithmetic, the post-payment costs that decide the last invoice, the utilization floor where a lease stops paying, and why a custom machine is priced worse than a catalogue one.

A coil line lease is cheaper per month and dearer per machine hour, and the two numbers answer different questions.
A Tier 2 stamping plant in Eastern Europe priced a 1,300 mm line at 180,000 USD last autumn. The bank quoted 6.5 percent over five years. The lessor quoted 2.35 percent a month for 48 months.
Monthly, that is 2,817 USD against 4,230 USD. Over five years it is 205,020 USD against 221,040 USD. Neither figure is wrong, and neither one settles the purchase.
Where the Monthly Payment Actually Goes
Equipment leases are quoted as a rate factor: the monthly payment expressed as a percentage of the machine price. Multiply the factor by the price and the payment falls out.
On this line the factor is 2.35 percent, so 180,000 USD becomes 4,230 USD a month for 48 months. Total paid across the term: 203,040 USD.
That is 23,040 USD above the price, or 12.8 percent of it, spread over four years. The outstanding balance falls from the full price to zero, so the average balance sits near half.
Twelve point eight percent over four years on half the principal is about 6.4 percent a year. The bank loan at 6.5 percent is the same cost of money wearing a different shape.
What separates the two products is not the interest. It is the residual value the lessor is assuming, and every condition attached to that assumption.
A lessor pricing a standard 1,300 mm line expects to resell it for 25 to 35 percent of new price after four years. That expectation sets the factor, and it explains why a custom machine is priced worse.
The factor also carries the lessor's administration and the credit risk they take on your plant. Neither appears as a line item, and both move with the size of the down payment.

Five-Year Arithmetic on a 180,000 USD Line
Four structures were priced against the same machine. The table holds total cash out, not the monthly figure, because the monthly figure is the one that hides the difference.
| Structure | Cash out over five years | What it does to the balance sheet | Where it costs you |
|---|---|---|---|
| Cash purchase, 3 percent settlement discount | 174,600 USD | Machine becomes a depreciating asset | Ties up capital the next press needs |
| Bank loan, 20 percent down, 6.5 percent, 60 months | 36,000 plus 169,020 = 205,020 USD | Debt and asset both on the books | Down payment plus covenant headroom |
| Lease, 48 months, 10 percent buyout | 203,040 plus 18,000 = 221,040 USD | Off balance sheet until buyout | 46,440 USD more than cash, plus a return standard |
| Lease, 60 months, machine returned | 212,400 USD, no asset at the end | Lowest monthly charge, no ownership | Payments continue after the work may have moved |
The gap between cash and the 48-month lease is 46,440 USD, roughly a quarter of the machine price.
Whether that gap is expensive depends on what the 174,600 USD would have done elsewhere. At a 5 percent return it earns about 43,650 USD over the same five years, which closes most of the distance.
At 2 percent, in a plant that keeps cash idle by habit, the lease is a 46,000 USD convenience. That is a capital allocation decision, not a machine decision.
Specifications that drive the price are laid out in the machinery specification index, and the ones worth paying for are a shorter list than most quotations suggest.
Costs That Arrive After the Final Payment
A lease is priced on the assumption that the machine returns in a defined condition. That definition is where the last invoice is written.
Rolls cause most of the arguments. A line that ran three shifts for four years will show worn roll surfaces, and re-chroming nine work rolls runs 6,000 to 9,000 USD.
If the handback clause demands original tolerance, that bill lands on the lessee four years after the budget was signed off and long after the job was quoted.
De-installation, crating and freight back to the lessor's yard add 3,000 to 6,000 USD inside a 40-foot container, and the clause normally names the lessee for all three.
Insurance is written for full replacement value, which is higher than the book value a plant would otherwise carry, so the premium line moves up as well.
- Buyout price, and the date on which it is fixed rather than estimated
- Return standard for roll surfaces, paint and guards, in measurable terms
- Who pays de-installation, crating, export paperwork and return freight
- Consent needed for relocation, added equipment and mid-term upgrades
- Insurance basis, named loss payee and who absorbs a shortfall
- End-of-term notice window, frequently 90 to 180 days before expiry
Reading a Rate Factor in Ten Seconds
Multiply the factor by the term in months. The product is everything paid as a percentage of the machine price, before buyout and fees.
1.95 percent over 36 months gives 70.2 percent. 2.35 percent over 48 months gives 112.8 percent. 2.05 percent over 60 months gives 123 percent.
Anything above roughly 115 percent on a 48-month term is more than 7 percent a year on average balance, which is where a bank loan normally wins.
The factor never includes the buyout, the documentation fee or the payment taken at signing. Ask for the sum of all payments plus buyout before comparing two offers.
- Term in months, multiplied by the factor, gives total paid as a percentage of price
- Anything over 115 percent on 48 months is above 7 percent a year on average balance
- Buyout, documentation fee and signing payment sit outside the factor entirely
- A factor quoted on a 60-month term cannot be compared with a 48-month one without the product
The Utilization Floor Where a Lease Stops Paying
A lease turns a capital cost into a fixed annual charge of about 44,208 USD on this machine. Divide that by hours and the shape of the decision becomes visible.
At 2,000 hours a year, one shift of 220 days, the lease costs 22.10 USD per machine hour. At 4,400 hours it is 10.05 USD. At 6,000 hours it is 7.37 USD.
Below about 1,500 hours a year, a used machine bought outright or a short rental beats a 48-month lease on total cost by a wide margin.

Hours are not the only divisor. A plant running 2,000 hours but at 45 SPM instead of 90 earns half the parts from the same fixed charge, and the cost per thousand parts doubles.
That is why a lease should be tested against parts, not months. Divide the annual charge by the parts the line actually ships and the answer usually looks worse than the monthly quote.
The second floor is contract length. When the work is a two-year programme, a five-year lease leaves three years of payments with no job behind them.
A lease is a wager that the machine earns for the whole term. A plant that cannot see four years of load should not sign four years of payments.
Where the Model Breaks on a Custom Machine
Residual value is the engine of the whole structure, and a bespoke line has almost none.
A 1,600 mm machine built at a non-standard height with a special coil car has no second buyer in the lessor's market. Expect the factor to rise 0.4 to 0.6 points and the deposit to reach 25 to 30 percent.
Build time is the second break. A six-month build means progress payments to the builder, and a lease that begins at delivery does not fund them. The buyer carries the construction and leases the finished machine.
Personal guarantees surface at that point. A small plant leasing a custom line is often asked for a director's guarantee, which removes most of the off-balance-sheet argument that started the conversation.
The arithmetic here also assumes the machine is standard enough to be repossessed and resold. On a one-off line the lessor is lending against the buyer's balance sheet, not against the asset.
Four questions come back from plants comparing the two offers.
At what rate factor does a 48-month lease beat a bank loan?
Below about 2.30 percent a month, or 110 percent of price across the term. Above that, a loan with 20 percent down is cheaper on total cash if the down payment is available.
How much does a 10 percent buyout add to a 48-month lease?
18,000 USD on this machine, paid in year five when the asset is already four years old. Total cost becomes 122.8 percent of the original price.
Does a coil line lease cover installation and commissioning?
Rarely. Rigging, foundation work, power connection and commissioning of 8,000 to 15,000 USD are usually cash items outside the lease and outside the rate factor.
How many hours a year must the line run to keep lease cost under 10 USD per machine hour?
About 4,400 hours, which is two shifts across 220 working days. Under that level the fixed charge dominates the cost of every part produced.
Where to go next
Finance structure is one line in a quotation that carries fifteen. The other fourteen decide whether the machine is worth financing at all.
Our coil line knowledge base takes each specification line and shows what it adds to the landed price, which is the arithmetic to finish before a lessor is called.
Read the specification cost guide